Vintage cabinets, like those from the 1800s, have a long and storied history.
They’re so important, in fact, that many collectors are still trying to figure out how to make their own.
Here are some tips to help you out.
Learn what type of cabinet you want.
When buying an antique cabinet, look for the type of wood used in it.
Wood from old-growth forests like spruce or beech are often preferred.
Beech wood can be used for many types of cabinets, but for some, the wood is also a key ingredient in making the cabinets look unique.
If you don’t have access to a local lumber yard, consider going with a commercial lumber yard or home improvement store that stocks wood from reputable lumber companies.
These companies will also supply you with the materials to build your own cabinet.
Choose a cabinet.
While some antique cabinets are made by hand, some cabinets can be made with a machine.
The best time to get a machine is when you’re not planning on having many hours in the day, so you can work with it.
If your plan is to keep the cabinet for several years, you can get one from a thrift store or a local hardware store.
If it’s a project you have on the way, a good budgeting tool is a home improvement supply shop.
Check out the cabinet.
Once you’ve narrowed down the materials and the materials you need, the next step is to make a cabinet out of them.
This is easier said than done.
The cabinets you see at thrift stores and home improvement stores can be quite large and difficult to assemble.
You’ll have to use a little imagination and patience to get everything lined up correctly.
Once everything is assembled, you’ll need to trim it down to size.
A good rule of thumb is to use two or three 1-by-2-inch pieces of plywood to form the cabinet, then trim the excess wood with a saw or jigsaw.
You can trim the whole thing with the saw, but be careful not to cut through the back, which will tear off the back of the cabinet and damage it.
For larger cabinets, you might want to use three or four pieces of wood.
This can be a pain in the butt.
Make sure to get two or more cabinet screws, so that you can secure them to the cabinet when you assemble it. 4.
Set up the cabinet’s base.
Next, you want to secure the top and bottom of the unit.
This should be something that sits on a table, on a countertop or in a closet.
This will make it easier to position the unit in the center of the room.
When assembling the cabinet base, the two sides should sit flush with the wall, so there’s not too much of a gap.
Cut out the top.
To begin cutting the cabinet out, you need to cut a piece of ply board, about 1-1/4 inches wide by 1-inch thick.
For the cabinet to sit flush against the wall and be sturdy, you should use a cutting board that is about 2-by 3-inches wide and 3-by 4-inches high.
A wood cutter or a router will do. 6.
Cut the bottom.
Cut two 2-inch strips of wood, about the size of your thumb, and put them on top of the ply board.
These strips should sit about 1/8-inch apart.
Make a slit in the backside of the top, so the ply can slide down.
This slit should be 1/2- inch deep, so when the ply slides down, you don’ t have to worry about the back side of the board sticking out.
Cut a second 2- by 3-inch strip of wood for the back.
Cut another 1/4-inch slit in both strips of ply.
These two strips should be about 1 1/16-inch from the back edge of the back and 1 1 /2-inches deep.
Cut three more strips of 2- inch wood, each about the same size as the first.
Cut about the exact same amount of space as the back strip, but cut it just slightly more narrow.
Secure the sides with screws.
Screw the back panel into the ply, making sure the ply and the back panels sit flush.
For extra security, make sure to attach the back pieces to the ply with the same screws that you used to secure it to the wall.
Test the cabinet by positioning the back piece on top and the front piece on the back surface of the wall with a ruler.
You should see that the back is sitting flush with a straight edge.
If the back edges aren’t perfectly level, it’s likely that you need more screws.
Be sure to test it with a light tap on the front side of your cabinet.
If everything goes as expected, the back should look smooth